BODYCAM 4: Basic Clip Information

Camera Mounting

The BODYCAM 4 has multiple mounting options available for purchase; all mounts attach to the rear of the camera on the sliding rail.

BC4-various-mounts.png

Rotating Garment Clip

The rotating garment clip (P/N: BC4-MNT-GAR) is a simple mounting method that attaches to a garment with a spring-loaded plastic clip. The clip can rotate 360° to allow it to attach to the garment at different angles. The inner portion of the clip has interlocking teeth to provide a grip onto the attachment point of the garment.

BC4-clip.png

Mounting:

To install the mount onto the camera, simply slide the mount upward into the slot on the rear of the camera until it clicks into place. The mount can be left attached to the camera in the docking station.

Removal:

To remove the mount, rotate the clip so it is perpendicular to the camera body; this provides access to the retention tab. Hold the camera with one hand and the clip with the other. Push the retention tab on the clip away from the camera body while simultaneously sliding the clip down and out of the camera slot.

Heavy-Duty Magnet Mount

The magnet mount (P/N: BC4-MNT-MAG/9000016/REV 02) consists of two parts: the inner mount, and the outer mount. The inner mount is placed behind the garment and the outer mount is placed on the outside of garment holding the mount in place with strong magnets.

BC4-magnet-mount.png

Mounting:

  1. Slide the camera down onto the outer mount until it clicks in place.
  2. Place the inner mount behind the garment in the desired mounting area.
  3. Hold camera with attached outer mount over the garment in front of the inner mount and they will attach magnetically.

Removal:

  1. Firmly grasp the side rails of the outer mount and tip assembly right or left to separate the mount, then pull the outer mount away to remove.
  2. Remove the inner mount from behind the garment.

Storage:

It is best to store the mounts with only two of the magnets on each portion connected for easy separation.

Safety Information:

Individuals with pacemakers or internal medical devices should use caution when handling the BODYCAM 4 magnetic mount. Magnetic fields may affect the operation of these devices. Consult with your physician and the manufacturer of your medical device to determine its susceptibility to static magnetic fields before handling the magnetic mount. Individuals with pacemakers and other internal medical devices that could potentially be affected by static magnetic fields should not wear the magnetic mount.

The BODYCAM 4 Magnetic Mount contains strong magnets and can pose a pinch-point hazard. Exercise caution when separating and connecting the outer and inner magnetic mount. When connecting the two pieces, ensure that all body parts are clear as the magnets will snap together.

Molle Mount

The Molle mount (P/N: BC4-MNT-MOL) is designed to attach to Molle vests and jackets. The mount consists of an adapter that mounts to the rear of the camera and the Molle mount that is attached to the Molle vest or jacket. The mount can be left attached to the vest or jacket while the camera is removed for charging and upload. To attach the camera, slide it down into the mount until it clicks. To remove the camera, rotate it 180° and slide upward to remove.

BC4-molle-mount.png

BC4-molle-mount-bracket.png

Epaulette Mount

The epaulette mount (P/N: BC4-MNT-EPL) is designed to attach to the epaulette on the shoulder of a uniform. This mount can only effectively be used if the uniform has epaulettes. The mount consists of an adapter that mounts to the rear of the camera and the mounting portion that is attached to the garment’s epaulette. The mount can be left attached to the vest or jacket while the camera is removed for charging and upload. To attach the camera, slide it down into the mount until it clicks. To remove the camera, rotate it 180° and slide upward to remove.

BC4-epaulette-mount.png

BC4-epaulette-mount-2.png

BC4-epaulette-mount-3.png

Screw-to-fit Mount

The screw-to-fit mount (P/N: BC4-MNT-STF) is a durable mount that is intended for use in applications where a garment is too thick for a magnet mount, and/or does not have provisions for attaching a clip. Typically, this mount is used in applications where heavy coats or outer vests are worn. The mount is semi-permanently attached to the garment using a backing plate and screws. The mount is machine washable so it can stay attached to the clothing indefinitely. Using this mount will leave 4 small holes in the garment and may deform the shape of the garment surface over time. The mount consists of an adapter that mounts to the rear of the camera and the mounting portion that is attached to the garment’s epaulette. The mount can be left attached to the vest or jacket while the camera is removed for charging and upload. To attach the camera, slide it down into the mount until it clicks. To remove the camera, rotate it 180° and slide upward.

BC4-screw-to-fit-mount.png

BC4-screw-to-fit-mount-2.png

Screw-on Mount

The screw-on mount (P/N: BC4-MNT-SCO) is intended to be used in applications where the camera will be mounted to a fixed bracket, wall, or other non-user-mounted application. Attach the mount to the surface using four (4) suitable mounting screws for the desired surface. Attach the mount to the rear of the camera as shown. To attach the camera, slide it down into the mount until it clicks. To remove the camera, rotate it 180° and slide upward to remove.

BC4-screw-on-mount.png

BC4-screw-on-mount-2.png

 

Was this article helpful?
1 out of 1 found this helpful

Comments

0 comments

Please sign in to leave a comment.

Articles in this section

See more
Our helpline hours:
8:00am - 7:00pm EDT Monday to Friday
Follow us on LinkedIn
Get the latest news and updates first
YouTube Support
Fow how-to and support videos please visit our channel